钻井液在致密砂岩中裂缝的侵入深度模型

克深井区储层的孔隙结构与裂缝特征造成钻井过程中钻井液大量漏失,其中的固相颗粒会堵塞裂缝,使得部分生产井在完井后产量偏低甚至无产量,现场主要是通过酸压来解决这类问题。对于裂缝性气藏的酸压而言,需要知道钻井液在裂缝中的侵入深度变化,以便于设计施工参数,评价酸压效果。针对这一问题,根据牛顿流体在裂缝中的流动机理,裂缝宽度的变化以及裂缝壁面的滤失等,建立了钻井液在单一裂缝中的漏失动力模型,根据裂缝内钻井液压力的分布来定量描述钻井液的侵入深度,考虑并分析了该模型的侵入深度与侵入时间,压差和裂缝宽度之间的相互关系。最后,利用该模型计算了克深井区获得增产效果的酸压井中钻井液的侵入深度和酸液的侵入深度,通过增产井中二者之间的关系,从而间接证明了该模型。     

油田埋地碳钢管道外腐蚀行为研究

针对大庆油田龙虎泡作业区埋地碳钢管道外腐蚀较为严重的情况,通过检测埋管防护层破损点周围土壤的物理、化学性质和硫酸盐还原菌（SRB）数量,分析土壤的腐蚀性。采用扫描电镜能谱（SEM-EDS）、X射线衍射（XRD）和红外光谱（IR）等技术对管道外壁腐蚀物的形貌、元素组成和矿物成分等进行了表征和分析。借助动电位极化曲线和电化学阻抗谱（EIS）进一步研究了埋地碳钢管道外壁在土壤浸出液中的腐蚀行为。结果表明,作业区潮湿的盐碱性土壤环境和复杂多变的土壤性质使该地区埋地碳钢管道发生腐蚀;腐蚀产物主要包括Fe₃O₄和FeOOH,其中FeOOH位于外层,Fe₃O₄位于内层;腐蚀产物通过参与阴极反应或充当大阴极来加剧管道腐蚀。     

弹体侵彻钢筋混凝土靶开坑深度研究

研究弹体侵彻靶板的开坑深度,有助于提升侵深和过载的计算精度.首先,通过总结对比现有的开坑深度模型以及试验数据的回归分析,建立了考虑弹体质量和初速度的开坑深度模型.然后,以此为基础给出了弹体侵彻钢筋混凝土靶开坑深度的计算方法.最后,结合作者早前建立的钢筋混凝土动态球形空腔膨胀理论,利用文献试验数据对开坑深度模型进行了应用对比分析.本文模型考虑了弹体质量、初速度以及首层钢筋网埋设深度等因素的影响,可用于分析不同质量、不同初速度弹体侵彻钢筋混凝土靶的开坑深度.      

Nanoindentation response analysis of TiN-Cu coating deposited by magnetron sputtering

To investigate the change of the mechanical properties of soft metals doped PVD(Physical Vapor Deposition)coatings after the migration of soft metal to the surface, TiN-Cu coating was deposited on Si(100) by magnetron sputtering. The microstructure and mechanical properties at room temperature and after vacuum heat treatment at 300 ℃ were investigated. The results showed that the grains were clustered and the microstructure was porous for TiN-Cu coating at room temperature, while many micro-and nano-sized Cu particles were observed on the surface after vacuum heat treatment at 300 ℃. The elastic properties of the TiN-Cu coating after vacuum heat treatment at 300℃ degraded compared with that at room temperature. The hardness and elasticity modulus of TiN-Cu coating kept constant(3.7 GPa and 125.0 GPa, respectively) with the increase of nano-indentation depth, while the hardness and elasticity modulus of TiN-Cu coating after vacuum heat treatment at 300 ℃ increased gradually.     

Terrestrial isopods and myriapods in a forested scree slope: subterranean biodiversity,depth gradient and annual dynamics

Diversity, depth distribution and seasonal activity of isopods and myriapods were studied using subterranean traps buried in a forested limestone scree slope in the ?ierna Hora Mts, Western Carpathians, Slovakia, throughout the depth gradient from 5 to 95 cm. A total of five isopod, 13 diplopod and 11 chilopod species were identified. Most edaphic species strongly preferred the uppermost organic soil layers. Among the species captured, some represented rare stenoecous Carpathian endemics, namely the isopod Trichoniscus carpaticus, and diplopods Julus curvicornis and Leptoiulus mariae. Others were subterranean forms, partly adapted to hypogean conditions: the isopod Mesoniscus graniger, and diplopods Mecogonopodium carpathicum and Trachysphaera costata. The annual activity in the vast majority of the species ceased completely in winter, and was gradually relaunched in spring. In evaluating the age structure of two predominant diplopods Polydesmus denticulatus and Mecogonopodium carpathicum, both widespread across the depth gradient, a vertical segregation of early post-embryonic stages was found. While P. denticulatus tended to undergo the early stages of development in the soil-filled topmost levels, the early juvenile stage of M. carpathicum was distributed deep in the scree slope profile.     

Studies on induction hardening of powder-metallurgy-processed Fe-Cr/Mo alloys

Induction hardening of dense Fe-Cr/Mo alloys processed via the powder-metallurgy route was studied. The Fe-3Cr-0.5Mo, Fe-1.5Cr-0.2Mo, and Fe-0.85Mo pre-alloyed powders were mixed with 0.4wt%, 0.6wt%, and 0.8wt% C and compacted at 500, 600, and 700 MPa, respectively. The compacts were sintered at 1473 K for 1 h and then cooled at 6 K/min. Ferrite with pearlite was mostly observed in the sintered alloys with 0.4wt% C, whereas a carbide network was also present in the alloys with 0.8wt% C. Graphite at prior particle boundaries led to deterioration of the mechanical properties of alloys with 0.8wt% C, whereas no significant induction hardening was achieved in alloys with 0.4wt% C. Among the investigated samples, alloys with 0.6wt% C exhibited the highest strength and ductility and were found to be suitable for induction hardening. The hardening was carried out at a frequency of 2.0 kHz for 2-3 s. A case depth of 2.5 mm was achieved while maintaining the bulk (interior) hardness of approximately HV 230. A martensitic structure was observed on the outer periphery of the samples. The hardness varied from HV 600 to HV 375 from the sample surface to the interior of the case hardened region. The best combination of properties and hardening depth was achieved in case of the Fe-1.5Cr-0.2Mo alloy with 0.6wt% C.     

预应力加载条件下零件干磨削表面强化层特征

采用预应力复合干磨削加工技术,对未调质45#钢试件在不同预应力加载条件下实施表面磨削淬硬,观测不同磨削深度和进给速度条件下的试件表层金相组织,测量并分析试件在不同预应力条件下磨削淬硬层厚度、金相组织的变化状况,并通过试件截面不同位置硬度测定显示淬硬层厚度及金相成分的变化,得到试件施加预应力对淬硬强化层厚度的影响规律.研究表明,预应力淬硬磨削能使工件表面产生强化层,且大的磨削深度和小的进给速度有利于试件表面发生相变强化以及表层塑性变形的增大.     

A survey of occlusion detection method for visual object

Occlusion problem is one of the challenging issues in vision field for a long time , and the occlu-sion phenomenon of visual object will be involved in many vision research fields .Once the occlusion occurs in a visual system , it will affect the effects of object recognition , tracking, observation and operation , so detecting occlusion autonomously should be one of the abilities for an intelligent vision system .The research on occlusion detection method for visual object has increasingly attracted atten-tions of scholars .First, the definition and classification of the occlusion problem are presented . Then, the characteristics and deficiencies of the occlusion detection methods based on the intensity image and the depth image are analyzed respectively , and the existing occlusion detection methods are compared.Finally, the problems of existing occlusion detection methods and possible research directions are pointed out .     

基于语义约束与Graph Cuts的稠密三维场景重建

本文提出一种新颖、有效的稠密三维场景重建算法.在城市建筑场景的重建中,为了快速恢复稠密、准确的深度信息,本文算法首先在视图中对建筑区域进行了语义分割以降低非重建区域(如天空、地面等)的干扰,在提高整体重建速度的同时也增强了采用平面模型对其进行重建的可靠性;然后,在通过基于DAISY特征的空间点扩散方法获取的初始深度图的基础上,针对传统算法难以重建的弱纹理、倾斜表面等区域,本文算法依据场景分段平滑的假设,在超像素级MRF能量优化框架中对其相应的空间平面进行了推断.由于能量函数融合了初始深度图的约束、空间平面先验及空间平面间的几何关系等信息,而且候选平面集通过平面拟合和已知平面约束下的多方向平面扫描两种方法构造,使得相应的两阶段迭代Graph Cuts对能量函数的求解更快速和精确.在标准数据集和真实数据上的实验表明,本文算法能有效克服光照变化、透视畸变、弱纹理区域等因素的影响,快速恢复建筑区域完整的深度图.     

渤海湾盆地济阳坳陷孤岛下古生界碳酸盐岩潜山油气成藏特征

位于沾化凹陷的孤岛下古生界碳酸盐岩潜山为菱形断块山, 边界断裂为多条断层构成的断裂带, 潜山主体构造呈短轴穹隆构造, 潜山为多期构造叠合的继承性隆起构造.潜山下古生界碳酸盐岩储层储集空间有晶间孔和晶间溶孔、粒间孔和粒间溶孔、铸模孔、砾内-砾间孔和砾内-砾间溶孔、溶洞、溶蚀缝和构造缝、方解石晶簇间孔等.储层基质孔隙度大部分低于2%,孔隙度随深度变化不大; 渗透率从几十个10-3 μm2到0.0001×10-3 μm2,渗透率随孔隙度的增大而增大.潜山的生储盖组合为下生上储顶盖型,但油源侧向运移.油气成藏特征有南北逢源、复式立体输导、高凸指向、混源充注、断层控制、缝洞发育、逸顶"天窗"和局部成藏等.由于孤岛潜山长期隆起,潜山顶部位缺失1.84 km2东营组,直接与馆下段砂砾岩体相接,形成一个油气向上逸散的"天窗".这是导致潜山不能大规模聚集油气的重要原因.